Digium Wildcard TE410P

VoIP Hardware Solutions
Provider Solution Details
VoIP Hardware Zycoo UC Solutions
  • Modular Design IP PBX for SMB
  • Remote office Centralized Management solution
  • 3rd party app integration, Enterprise Billing, Android & iOS client
Details
Yeastar Communications Solutions
  • Cost-effective IP-PBX Solution for SMB
  • FXS, FXO, GSM, BRI and PRI VoIP Gateways
  • Rich features and reliable performance
Details
Image


The TE410P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture. The TE410P supports both E1 and T1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1 and T1 equipment and allows inexpensive T1 channel banks to connect with E1 circuits. Because the TE410P improves I/O speed by up to 10 times, the result is reduced CPU usage and increased card density per server.

Digium has designed the TE410P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.

The TE410P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features.

The TE410P supports a 3.3v PCI slot only - typically available on newer motherboards and in 64-bit PCI bus architectures. The TE405P is for use only with a 5.0 volt PCI slot.

Documentation


Data Modes: for the TE410P
Cicso HDLC
HDLC
PPP
Multilink PPP
Frame Relay
Voice Modes:

PRI CPE & PRI NET


NI1
NI2
EuroISDN for the TE410P
4ESS (AT&T)
5ESS (Lucent)
DMS100

E&M


Wink
Feature Group B for the TE410P
Feature Group D

FXO & FXS


Ground Start
Loop Start for the TE410P
Loop Start with Disconnect Detect

Certifications:


Telecom FCC Part 68 (TIA-968-A), IC CS-03, TBR 4, TBR 12, TBR 13, AS/ACIF S038, AS/ACIF S016 for the TE410P
Safety UL/CSA 60950, IEC 60950, EN60950, AS/NZS 60950

Note: Finland, Norway and Sweden require that equipment using this product must be located in a Restricted Access Location (RAL).
Emissions: EN55022 Class B Radiated & Conducted
Immunity: EN55024 ITE, EN61000

See also


Where To Buy


.e4 Tech - The Internet's premiere resource for all Asterisk related hardware
digiumcards.com - The Internet's premiere resource for all Asterisk related hardware
VoIPandGo Cheap Prices! Great Service! Quick delivery by UPS.
VoIPon - Worldwide
Image


The TE410P is the next generation of Digium hardware that improves performance and scalability through bus mastering architecture. The TE410P supports both E1 and T1 environments and is selectable on a per-card or per-port basis. This feature enables signaling translation between E1 and T1 equipment and allows inexpensive T1 channel banks to connect with E1 circuits. Because the TE410P improves I/O speed by up to 10 times, the result is reduced CPU usage and increased card density per server.

Digium has designed the TE410P to be fully compatible with existing software applications and it is fully integrated with the Asterisk Open Source PBX/IVR platform. Also, the open source driver supports an API interface for custom application development. With the combination of Digium Hardware and Asterisk software, numerous combinations of telephony configurations are possible. From the traditional PBX to VoIP Gateways, Digium solutions are paving the way for a new generation of worldwide communications.

The TE410P supports industry standard telephony and data protocols, including Primary Rate ISDN (both N. American and Standard Euro) protocol families for voice, PPP, Cisco, HDLC, and Frame Relay data modes. Both line-side and trunk-side interfaces are supported, also included are advanced call features.

The TE410P supports a 3.3v PCI slot only - typically available on newer motherboards and in 64-bit PCI bus architectures. The TE405P is for use only with a 5.0 volt PCI slot.

Documentation


Data Modes: for the TE410P
Cicso HDLC
HDLC
PPP
Multilink PPP
Frame Relay
Voice Modes:

PRI CPE & PRI NET


NI1
NI2
EuroISDN for the TE410P
4ESS (AT&T)
5ESS (Lucent)
DMS100

E&M


Wink
Feature Group B for the TE410P
Feature Group D

FXO & FXS


Ground Start
Loop Start for the TE410P
Loop Start with Disconnect Detect

Certifications:


Telecom FCC Part 68 (TIA-968-A), IC CS-03, TBR 4, TBR 12, TBR 13, AS/ACIF S038, AS/ACIF S016 for the TE410P
Safety UL/CSA 60950, IEC 60950, EN60950, AS/NZS 60950

Note: Finland, Norway and Sweden require that equipment using this product must be located in a Restricted Access Location (RAL).
Emissions: EN55022 Class B Radiated & Conducted
Immunity: EN55024 ITE, EN61000

See also


Where To Buy


.e4 Tech - The Internet's premiere resource for all Asterisk related hardware
digiumcards.com - The Internet's premiere resource for all Asterisk related hardware
VoIPandGo Cheap Prices! Great Service! Quick delivery by UPS.
VoIPon - Worldwide
Created by: VoIPon, Last modification: Mon 24 of Oct, 2011 (20:27 UTC) by admin
Please update this page with new information, just login and click on the "Edit" or "Discussion" tab. Get a free login here: Register Thanks! - Find us on Google+