Using Software version 10.1.0

Here's what I did:

1. Create a Media Profile (called "voip")
name* = voip
active = yes
protocol-type = sip

[in MEDIA-GATEWAY/voip:voip-options]
packet-audio-mode = g711-ulaw
frames-per-packet = 2
silence-det-cng = no
ena-adap-jitter-buffer = yes
max-jitter-buffer-size = 19
initial-jitter-buffer-size = 2
voice-ann-dir = /current
voice-ann-enc = g711-ulaw
call-inter-digit-timeout = 6000
silence-threshold = 0
dtmf-tone-passing = inband
maxcalls = 672
rfc2833-payload-type = 96
g711-transparent-data = no
rtp-problem-reporting = { no 30 60 }

[in MEDIA-GATEWAY/voip:sip-options]
t1-timer = 500
t2-timer = 4000
invite-retries = 6
non-invite-retries = 10
primary-proxy = { x.x.x.x "" 5060 compact } (IP ADDRESS OF ASTERISK)
secondary-proxy = { 0.0.0.0 "" 5060 compact }
registration-proxy = { x.x.x.x "" 5060 compact 1 } (IP ADDRESS OF ASTERISK)
proxy-heartbeat = 0
proxy-failover-window = 60
reroute-on-proxy-failure = no
trusted-proxy =
unknown-ani = ""
blocked-ani = ""
privacy-proxy-require = disabled
cause-code-map = s
start-call-method = invite
trunk-group-options =
onhold-minutes = 0

support-100rel = disabled
internationalize = no
international-prefix = no
country-code = ""
national-destination-code = ""
local-number-ton = unknown-ton
call-transfer-method = ip-transfer
notify-timer = 0
invite-with-multiple-codecs = disabled

2. Configure Call Route for Digitam Modem card

admin> get call-route {{{1 3 0}0}0}
[in CALL-ROUTE/{ { { shelf-1 slot-3 0 } 0 } 0 }]
index* = { { { shelf-1 slot-3 0 } 0 } 0 }
active = yes
trunk-group = 0
phone-number = 7299 (last 4 digits of your DID)
preferred-source = { { any-shelf any-slot 0 } 0 }
call-route-type = voice-call-type
cost = 0

3. Configure the T1 ports

default-call-type = dnis-or-voip
media-gateway = voip

I did this about 8 months ago and don't have my notes with me so I hope
I remembered everything. Give it a shot. Good luck

- Darren

[maxtnt]
type=friend
host=xxx.xxx.xxx.xxx
dtmfmode=inband
callerid="MaxTNT" <maxtnt>
context=toll-access
qualify=yes
reinvite=no
canreinvite=no
disallow=all
allow=g729
allow=ulaw

[toll-trunks]
;
; Outbound 1-nxx-nxx-xxxx goes via: PSTN
;
exten => _1NXXNXXXXXX,1,Dial(SIP/${EXTEN}@xxx.xxx.xxx.xxx,60)
exten => _1NXXNXXXXXX,2,Hangup

[local-trunks]
;
; Outbound to nxx-xxxx goes via: PSTN
;
exten => _NXXXXXX,1,Dial(SIP/${EXTEN}@xxx.xxx.xxx.xxx,60)
exten => _NXXXXXX,2,Hangup
;

[local-access]
;
; Extensions that are this context are allowed to only call local PSTN
numbers and other extensions
;
include => extensions
include => local-trunks         ; Access to Local numbers

[toll-access]
;
; Extensions that are this context are allowed to call local and long
distance PSTN numbers and other extensions
;
include => local-access         ; Everything local-access has
include => toll-trunks          ; Access to toll numbers

- Darren

kentec says:

output of 'show' command:
Shelf 1 ( standalone ):
                                Reqd  Oper   Slot Type
   { shelf-1 slot-1 0 }         UP    UP     ether3-card
   { shelf-1 slot-2 0 }         UP    UP     8t1-card
   { shelf-1 slot-3 0 }         UP    UP     madd2-card

obfuscation in config:
netmask /29 (255.255.255.248)
10.0.0.1 - ip gateway
10.0.0.2 - asterisk
10.0.0.3 - maxtnt

10.0.0.11 - syslog host
10.0.0.12 - ntp host
10.0.0.13 - dns host
10.0.0.14 - dns host

There are "notes" inline with the config. This is a 'save' style
config, so can be copy/pasted straight in to your console (after
adjusting anything obfuscated and adjusting for card slots)


; start config
; we use g711-ulaw, rfc2833 (rtp) dtmf
new MEDIA-GATEWAY
set name = voip
set active = yes
set protocol-type = sip
set mg-sig-address ip-address = 10.0.0.3
set mg-rtp-address ip-address = 10.0.0.3
set transport-options type = udp
set voip-options codec-options g711-ulaw dtmf-tone-passing = rtp
set voip-options codec-options g711-ulaw silence-det-cng = yes
set sip-options primary-proxy ip-address = 10.0.0.2
set sip-options registration-proxy ip-address = 10.0.0.2
set sip-options unknown-ani = 0000000000
set sip-options unknown-name = www.kci.net
set sip-options blocked-ani = 0000000000
set sip-options blocked-name = blocked
set sip-options trunk-group-options otg-tag = ""
set sip-options trunk-group-options otg-tag-in-userinfo = no
set sip-options trunk-group-options dtg-tag = ""
write -f
;
; saving profiles of type SSH-SERVER-CONFIG
new SSH-SERVER-CONFIG
set ssh-enabled = yes
set login-grace-time = 60
write -f
;
; saving profiles of type CALL-ROUTE
; note this is the '8t1-card'
; { { { shelf-1 slot-2 0 } 0 } 0 }
new CALL-ROUTE
set index device-address physical-address slot = slot-2
set call-route-type = trunk-call-type
write -f
;
; note this is the 'madd2-card'
; note i disabled all call-routes but
; index 0 (voice-call-type)
; index 5 (voip-call-type)
; { { { shelf-1 slot-3 0 } 0 } 0 }
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set call-route-type = voice-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 1
set active = no
set call-route-type = phs-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 2
set active = no
set call-route-type = wormarq-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 3
set active = no
set call-route-type = digital-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 4
set active = no
set call-route-type = v110-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 5
set call-route-type = voip-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 6
set active = no
set call-route-type = rtfax-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 7
set active = no
set call-route-type = g729-call-type
write -f
;
new CALL-ROUTE
set index device-address physical-address slot = slot-3
set index entry-number = 8
set active = no
set call-route-type = mtp-link-type
write -f
;
; saving profiles of type LOG
new LOG
set call-info = end-of-call
set syslog-enabled = yes
set host = 10.0.0.11
set syslog-format = max
write -f
;
; saving profiles of type T1
; we only get channelized t1 from our local telephone monopoly (LTM)
; esf/b8zs trunk, eight channels
; asterisk switchtype 'national' so maxtnt 'switch-type = nat-isdn-2-pri'
; one thing that caused us problems was that we would see the call ring
; across several channels but not get answered by the max. turns out
; our LTM has an older switch and wasn't catching the default short
; 200ms wink. 'robbed-bit-mode = inc-w-400' and joy for all.
; only first eight channels active, the rest 'channel-usage = unused-channel'
; LTM DTMF's the incoming did so 'collect-incoming-digits = yes'
; set 'voip-gain-control output-pad = 9db-loss' because it was way
; too hot out, causing echo and some funky artifacting
; set 'egress-ani-dnis-format = dnis' because LTM cries if we send the
; extra DTMF for ANI on some NXX
new T1
set name = trunkone
set physical-address shelf = shelf-1
set physical-address slot = slot-2
set physical-address item-number = 1
set line-interface enabled = yes
set line-interface frame-type = esf
set line-interface encoding = b8zs
set line-interface robbed-bit-mode = inc-w-400
set line-interface default-call-type = dnis-or-voip
set line-interface switch-type = nat-isdn-2-pri
set line-interface channel-config 1 trunk-group = 0
set line-interface channel-config 2 trunk-group = 0
set line-interface channel-config 3 trunk-group = 0
set line-interface channel-config 4 trunk-group = 0
set line-interface channel-config 5 trunk-group = 0
set line-interface channel-config 6 trunk-group = 0
set line-interface channel-config 7 trunk-group = 0
set line-interface channel-config 8 trunk-group = 0
set line-interface channel-config 9 channel-usage = unused-channel
set line-interface channel-config 10 channel-usage = unused-channel
set line-interface channel-config 11 channel-usage = unused-channel
set line-interface channel-config 12 channel-usage = unused-channel
set line-interface channel-config 13 channel-usage = unused-channel
set line-interface channel-config 14 channel-usage = unused-channel
set line-interface channel-config 15 channel-usage = unused-channel
set line-interface channel-config 16 channel-usage = unused-channel
set line-interface channel-config 17 channel-usage = unused-channel
set line-interface channel-config 18 channel-usage = unused-channel
set line-interface channel-config 19 channel-usage = unused-channel
set line-interface channel-config 20 channel-usage = unused-channel
set line-interface channel-config 21 channel-usage = unused-channel
set line-interface channel-config 22 channel-usage = unused-channel
set line-interface channel-config 23 channel-usage = unused-channel
set line-interface channel-config 24 channel-usage = unused-channel
set line-interface collect-incoming-digits = yes
set line-interface voip-gain-control output-pad = 9db-loss
set line-interface media-gateway = voip
set line-interface egress-ani-dnis-format = dnis
write -f
;
; saving profiles of type IP-ROUTE
new IP-ROUTE
set name = default
set gateway-address = 10.0.0.1
set metric = 1
set private-route = yes
write -f
;
; saving profiles of type IP-GLOBAL
new IP-GLOBAL
set domain-name = kci.net
set dns-primary-server = 10.0.0.13
set dns-secondary-server = 10.0.0.14
set system-ip-addr = 10.0.0.3
set sntp-info enabled = sntp-enabled
set sntp-info GMT-offset = utc-0700
set sntp-info host 1 = 10.0.0.12
write -f
;
new IP-INTERFACE
set interface-address physical-address shelf = shelf-1
set interface-address physical-address slot = slot-1
set interface-address physical-address item-number = 1
set ip-address = 10.0.0.3/29
set netmask = 255.255.255.248
write -f

-- kentec (running with this configuration for a month now with no issues)