QUIRK Anveo Direct - busy signal only - gave up.

[Robert.Thompson]

Hello:
Have been trying to set up Anveo Direct for the past few days but not succeeding.
Using Incredible PBX 12.0.70 on Ubuntu Server 14.04 x 64 DigitalOcean Droplet.
Have only proceeded to point of setting up incoming calls - have not proceeded to outgoing following 'SIPaholics Dream' tutorial.
When I dial the Anveo Direct DID, I get a busy signal.
There are no CDR records.
The asterisk log, for today, is attached.

This part, in particular, confuses me:
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'from-trunk-sip-anveo-5' tries to include nonexistent context 'from-trunk-sip-anveo-5-custom'
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'from-trunk-sip-anveo-4' tries to include nonexistent context 'from-trunk-sip-anveo-4-custom'
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'from-trunk-sip-anveo-3' tries to include nonexistent context 'from-trunk-sip-anveo-3-custom'
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'from-trunk-sip-anveo-2' tries to include nonexistent context 'from-trunk-sip-anveo-2-custom'
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'ext-trunk' tries to include nonexistent context 'ext-trunk-custom'
[2015-08-21 09:31:55] WARNING[16488] pbx.c: Context 'from-trunk-sip-anveo' tries to include nonexistent context 'from-trunk-sip-anveo-custom'

Can someone help me to get this to work?

Perhaps it is this instruction:

Step #2: Now access your hardware-based firewall and map incoming UDP port 5060 traffic to the IP address of your PBX in a Flash server. The exact steps vary slightly depending upon the type of router you have. Look for a tab that deals with redirecting Internet traffic through your router to destination IP addresses.

Is there something that I must do to my DigitalOcean droplet?

Thanks,

 

[Robert.Thompson]

The log shows this:
[2015-08-21 13:14:31] NOTICE[30643] chan_sip.c: Peer 'anveo-3' is now UNREACHABLE! Last qualify: 0
[2015-08-21 13:14:31] NOTICE[30643] chan_sip.c: Peer 'anveo-5' is now UNREACHABLE! Last qualify: 0
[2015-08-21 13:14:31] NOTICE[30643] chan_sip.c: Peer 'anveo-4' is now UNREACHABLE! Last qualify: 0
[2015-08-21 13:14:42] NOTICE[30605] res_pjsip/pjsip_distributor.c: Request from '"Robert Thompson" <sip:[email protected]>' failed for '50.22.101.14:5060' (callid: [email protected]-b2b_1) - No matching endpoint found

Does anyone have a suggestion?

Thanks,

 

[Robert.Thompson]

Here is an Anveo SIP Trace log

 

[Robert.Thompson]

Hello:

Can someone tell me if the following means that udp port 5060 is mapped to my servers ip address?

STARTING ASTERISK
Asterisk Started
root@uPBX:~# netstat -nlp | grep 5060
udp 0 0 0.0.0.0:5060 0.0.0.0:* 30577/asterisk
root@uPBX:~#

Thank you.

 

[Robert.Thompson]

OK, I give up.
Going back to the older version "Incredible PBX 11" which even I could get to work.

 

[Robert.Thompson]

Installed the older version and everything is working well.