DoppelGanger
New Member
- Joined
- Oct 14, 2011
- Messages
- 3
- Reaction score
- 0
I have been using PBX-IAF for quite a while and really enjoy all the hard work you all have put into it. Really enjoying the free calling to US & Canada this year.
I would consider myself a linux n00b, so the easiest way to get my status screen on here was to type it in:
PBX in a Flash Version = 1.7.5.7 Running on *VIRTUALBOX*
FreePBX Version = 2.8.1.4
Running Asterisk Version = 1.8.6.0
Asterisk Source Version = 1.8.6.0
Dahdi Source Version = 2.5.0.1+2.5.0.1
Libpri Source Version = 1.4.12
IP Address = 192.168.11.176 on eth0
Operating System = CentOS release 5.7 (Final)
Kernel Version = 2.6.18-274.3.1.e15 - 32 Bit
The issue is with just one phone number. Everything else works fine.
So yesterday I noticed there was a number that I could no longer call. It rings once or twice, then goes to a busy signal, even though the number is not busy. My friends at the other end of the line can call me from that number, but I am unable to successfully answer the call. I can answer the call, it acts as if it is connected, we can't hear each other and they go to voicemail after a few seconds.
Then I tried calling from Gmail chat phone, and it did not work either. So I submitted a help request to GV, and they did fix it- partially. Now I am able to call via Gmail chat phone, but not through my PBX-IAF. What confuses me is that this is the only number that this happens with.
Any ideas?
All suggestions tips and tricks are truly appreciated.
BONUS: How do I change my config so that I can call ten digit numbers with a 1 in front? Right now I can only call if in the following format: 555-666-1234. I know there is a way to route calls with the 1 in front properly, I just don't know how.
I would consider myself a linux n00b, so the easiest way to get my status screen on here was to type it in:
PBX in a Flash Version = 1.7.5.7 Running on *VIRTUALBOX*
FreePBX Version = 2.8.1.4
Running Asterisk Version = 1.8.6.0
Asterisk Source Version = 1.8.6.0
Dahdi Source Version = 2.5.0.1+2.5.0.1
Libpri Source Version = 1.4.12
IP Address = 192.168.11.176 on eth0
Operating System = CentOS release 5.7 (Final)
Kernel Version = 2.6.18-274.3.1.e15 - 32 Bit
The issue is with just one phone number. Everything else works fine.
So yesterday I noticed there was a number that I could no longer call. It rings once or twice, then goes to a busy signal, even though the number is not busy. My friends at the other end of the line can call me from that number, but I am unable to successfully answer the call. I can answer the call, it acts as if it is connected, we can't hear each other and they go to voicemail after a few seconds.
Then I tried calling from Gmail chat phone, and it did not work either. So I submitted a help request to GV, and they did fix it- partially. Now I am able to call via Gmail chat phone, but not through my PBX-IAF. What confuses me is that this is the only number that this happens with.
Any ideas?
All suggestions tips and tricks are truly appreciated.
BONUS: How do I change my config so that I can call ten digit numbers with a 1 in front? Right now I can only call if in the following format: 555-666-1234. I know there is a way to route calls with the 1 in front properly, I just don't know how.
